New Parts
16 - 7000 series cast guides                       28.80
8 - 30,000 series hard seats                       66.00
set - Stage 1 3/8 valves                            225.00
set - Stage 1 Plus                                       75.00
springs retainers & locks
8 - intake seals                                           15.12
set - rocker assemblies                             169.95
stock new push rods                                   39.95
master engine kit  (includes )                  1247.18
cast pistons, rings, bearings (includes T/A dual
groove cam bearings), gaskets
brass freeze & galley plugs, oil pump kit
Stage 1 plus cam, lifters, timing set
ARP rod bolts                                              78.95
Stage 1 fuel pump                                       49.95
8 - RTS-44ts spark plugs                            16.95
oil, filter, paint and materials                     119.50
core charge                                              500.00
total parts                                               2,933.33
total including
machine work, labor and parts             $6,938.33

This price does not include, crating, shipping or
applicable sales tax

With stock intake and Quadrajet this
combination makes 9.59 compression, idles well
and makes 30 more HP as a factory Stage 1
engine that had 3/4 of a point more
compression and will run on
unleaded  92 octane pump gas

We have included as standard in this
combination extras such as brass freeze plugs,
hardened exhaust seats, ARP rod bolts,
enhanced oiling, balancing, blueprinting,
dynamometer break-in and tune
Effective 1-1-2014
Price subject to change do to increases in costs
455 Street 1
400 + HP
455 Buick
manganese bronze valve guides                     101.20
will last thousands of miles longer

Edlebrock Performer or B4B intake                 312.00

Intake oil shield                                                 35.00

Holley 870 Avenger                                         399.95

Speed Pro forged pistons                                144.00

455 MSD ready to run distributor                    369.95

MSD blaster coil                                                43.95

7mm wire set                                                     39.95

custom Buick 8 mm wire set                             159.95
include wire separators and hold downs
rebuild point distributor                                    189.95
Includes new points, condenser, cap, rotor
vacuum advance and harness

rebuild point distributor                                    257.90
Includes new Crane Fireball electronic conversion
cap, rotor, vacuum advance and harness

rebuild HEI distributor                                     225.00
includes new magnetic pick-up, module,
wiring harness, cap, rotor and coil

Q-Jet Carb rebuild includes parts                    285.00
And recalibrate for larger cam  
(PLATING AVAILABLE)
455 Street 1 options

cylinder heads
oven bake & steelabrate                  54.00
magnaflux                                        35.00
replace guides                               144.00
install hardened seats                    112.00
stage 1 conversion                         240.00
performance valve job                    175.00
resurface heads                               75.00
install freeze plugs                             8.00

Block
pre-clean                                          45.00
oven bake & steelabrate                  85.00
re-surface deck                              150.00
align-hone                                      165.00
bore and hone with torque             240.00
plates ( street finish )
install cam bearings                         75.00
install galley & freeze plugs              33.00
modify oil passages                          85.00

Rods
oven bake & steelabrate                  28.00
re-size big end ( w/ARP )                224.00

Pistons
press off old and refit  new               80.00

Crankshaft
oven bake & steelabrate                  22.00
chamfer oil holes                              30.00
custom grind                                  155.00
balance assembly                          255.00

Labor
disassemble engine                       150.00
assemble                                        990.00
dyno break in and tune                  550.00

Total machine work & labor        
4,305.00  
Street 1 455 engines are meant for general street driving and are not intended for racing.
That does not mean that an occasional trip to the drag strip is out of the question
If you want more performance look at the Street 2 or Stealth engines